TP Link Weather Radio TL WR710N User Manual

Physical Description  
Connect the plug directly to the TL-WR710N to finish  
hardware connection.  
Package Contents  
The provided power plug may differ from the picture due  
to different regional power specifications. Here we use the  
EU version as an example.  
TL-WR710N LED:  
Note:  
Status  
Indication  
The device is working properly.  
System is booting.  
Solid Green  
Blinking  
The Ethernet Cable or USB Device is  
connecting to the product.  
Quick Installation Guide  
WiFi Pocket Router/AP/TV Adapter/Repeater  
USB Reset  
LAN/WAN  
LAN  
TL-WR710N  
Ethernet Cable  
After hardware connection, please write down the  
Wireless Password and SSID on the label of your  
Router for later use. Both are case-sensitive.  
USBIt is used to connect USB Flash or Hard Disk for ꢀle sharing and  
Mobile devices for charging.  
ResetIt is used to reset the Router to its factory defaults.  
Model:TL-WR710N  
S/N:XXXXXXXXXXXX  
Ver:2.0  
LAN/WAN: Must use this port to connect to your Modem while in  
Router mode. For all other modes, use it as an additional LAN port.  
MAC:B0487A663D6C  
WiFi Pocket Router/AP/TV Adapter/Repeater  
Wireless Password/PIN:12345678  
SSID:TP-LINK_663D6C  
LAN: Connect your ethernet enabled devices for wired network  
access. In client mode, use it to give wireless access to a wired-only  
device. In access point mode, use it to receive network access from  
your local network.  
WiFi Pocket Router/AP/TV Adapter/Repeater  
Model:TL-WR710N  
Ver:2.0  
S/N:XXXXXXXXXXXX  
Default Access:  
Username: admin  
Password  
:
admin  
MAC:B0487A663D6C  
MODEL NO. TL-WR710N  
Wireless Password/PIN:12345678  
SSID:TP-LINK_663D6C  
FCC ID: TE7WR710N  
IC: 8853A-WR710N  
Resource CD  
QIG  
Wireless Password/PIN: Default Password  
For more detailed information about Reset, please refer to  
*
*
Appendix: Troubleshooting  
.
SSID: Default Wireless Network Name  
MODEL NO. TL-WR710N  
Hardware Connection  
1
Wireless Router Mode (Default)  
2
Access Point Mode  
3
4
Client Mode  
5
WISP Client Router Mode  
Repeater Mode  
Create an instant private wireless network  
and share Internet to multiple Wi-Fi  
devices.This mode is suitable for hotel rooms  
and home networks.  
Create a wireless network from an Ethernet  
connection. This mode is suitable for dorm  
rooms or homes where there's already a wired  
router but you need a wireless hotspot.  
In this mode, this device can be connected to  
another device via Ethernet cable and act as  
an adapter to grant your wired devices  
access to a wireless network, especially for a  
Smart TV, Media Player, or Game console  
only with an Ethernet port.  
Use as  
access from  
Provider (WISP), and share that access with  
local devices.  
a
client router to receive Internet  
Wireless Internet Service  
Repeat signal from an existing wireless  
network. This mode is suitable to extend  
wireless coverage, reaching devices that  
were previously too far from your primary  
a
router to maintain  
connection.  
a
stable wireless  
(Note: if the hotel’s Internet has an  
authentication process, you will need to  
authenticate only once and only on one  
device.)  
(Note: if the hotel’s Internet has an authentica-  
tion process, you will need to authenticate it  
on EACH device.)  
The repeated signal will display the same  
network name and password as your existing  
wireless network.  
Wired Ethernet  
Connection  
Wired Ethernet  
Connection  
SSID: def  
Protected by  
NAT Firewall  
Cable  
Cable  
Instant Wireless Connection  
(The examples illustrated below are from Windows 7. If you are using a diꢁerent Windows, or a Mac Operating System, your screenshots may look diꢁerent, but the procedure is the same.)  
Go to Start  
network status and tasks  
adapter settings. Right click Wireless  
Network Connection, and select  
>
Control Panel  
>
View  
Set up the TCP/IP Protocol in "Obtain an IP  
address automatically" and "Obtain DNS  
sever address automatically" mode on your  
PC. Click OK.  
Click the Wireless Network icon  
desktop. Select the Default SSID of the  
TL-WR710N, then click Connect.  
on your  
Enter the Default Password. Click OK or  
Next.  
The ꢀgure below indicates you have  
successfully connected to your network.  
1
2
3
4
4
>
Change  
Properties. Double click Internet Protocol  
Version 4 (TCP/IPv4) in the item list.  
Operation Mode Conꢀguration  
Open  
a
Web browser and go to the page  
After a successful login, click “Quick Setup” from the menu  
to conꢀgure your TL-WR710N. Click “Next”.  
Choose the Working Mode you need, then click “Next” and  
refer to the corresponding mode on the back page for  
further instruction.  
1
2
3
http://tplinklogin.net. Enter the default User Name  
and Password: admin, both in lower case letters.  
Click OK.  
 

TDK Network Card HHM Series HHM1589D1 User Manual
Technicolor Thomson IP Phone TG787 User Manual
Timex Watch W 191 NA User Manual
Toastmaster Food Processor TMMC2 User Manual
Tripp Lite Network Cables P561 100 EZ User Manual
Vestax Musical Instrument PMC 07ProISP User Manual
ViewSonic Projector VS13338 User Manual
Vinotemp Refrigerator VT 6H User Manual
Walker Lawn Mower MT MTL MTEFI MTLEFI User Manual
Waves Stereo Equalizer EQP 1A User Manual