TP Link Network Router TR 966D User Manual

User's Guide  
TR-966D  
10/100Mbps WDM Fiber Bridge  
 
COPYRIGHT & TRADEMARKS  
Table of Content  
Specifications are subject to change without notice.  
is a registered trademark of TP-LINK  
Technologies Co., Ltd. Other brands and product names  
are trademarks or registered trademarks of their respective  
holders.  
No part of the specifications may be reproduced in any form  
or by any means or used to make any derivative such as  
translation, transformation, or adaptation without permission  
from TP-LINK Technologies Co., Ltd. Copyright @2006 TP-  
LINK Technologies Co., Ltd. All rights reserved.  
 
Auto-detection of half/full duplex transfer mode for RJ45  
port.  
TR-966D  
10/100M WDM Fiber Bridge  
Auto-negotiation of 10/100Mbps rate and Auto-MDIX for  
RJ45 port.  
TR-966D Front Panel  
Fiber port only support full duplex transfer.  
Extend fiber distance up to 20km for fiber port.  
Easy-to-view LED indicators provide status to easily monitor  
network activity.  
2. Rear Panel  
The rear panel of the TR-966D consists of one AC power  
connector, two 10/100Mbps RJ45 ports and two SC Fiber  
interfaces.  
External power supply.  
Network Cable Supported  
POWER  
T1  
T2  
F1  
F2  
The connectors and network cables supported by the TR-966D  
are listed in the following:  
TR-966D Rear Panel  
3. LED Indicators  
RJ45 port: Cat 5 Twisted-pair  
This TR-966D has LED indicators which can provide a real-  
time report. When you take a look at these indicators, you will  
know what’s happening your network.  
SC Fiber port: single-mode fiber cable  
Appearance Indication  
1. Front Panel  
Power(Red): Lights when the adapter is properly plugged in.  
T1_SPD/T2_SPD(Green): Light when the RJ45 port is  
connected to 100Mbps device; When the port connect to  
a 10Mbps device, the LED turns off.  
The front panel of the TR-966D consists of several LED  
indicators  
2
3
 
 
T1_Link/ Act/ T2_Link/ Act(Green): Steady green  
indicates that a valid link exists. Flashing green indicates  
that the TR-966D is receiving or transmitting data from the  
RJ-45 port.  
Make sure that the length of twisted pair cable (Category-  
5) between 10/100Base-TX device and converter is not  
longer than 100 meters.  
Connect one end of twisted pair cable to RJ45 jack on the  
TR-966D and the other end of the cable to the cable to  
the RJ-45 jack on the 10/100Base-TX device.  
F1_Link/Act/ F2_Link/Act (Green): Steady green  
indicates that a valid link exists. Flashing green indicates  
that the TR-966D is receiving or transmitting data from  
the fiber port.  
B. Connect the TR-966D to 100Base-FX Device  
Connection.  
Connect on (SC) end of a singl-mode fiber cable to the SC  
connector F1/F2 on the TR-966D and the other end of  
the cable to 100Base-FX device.  
Installation Guide  
1. Configuration  
In order to achieve the aim of effectively expanding a Fast  
Ethernet network, you can use the TR-966D as the example.  
C. Turn on the device.  
Notes:  
The WDM technology employs passive optic multiplexing,  
thus multiplex the transmit (TX) and receive (RX) lines onto a  
single fiber. WDM technology is implemented in couples. For  
example, one site uses the F1 fiber port on the TR-966D, the  
other site uses DEVICE A, the fiber port on DEVICE A must be  
1550nm/1310nm WDM fiber; One site uses the F2 fiber port on  
the TR-966D, the other site uses DEVICE B, the fiber port on  
DEVICE B must be 1310nm/1550nm WDM fiber.  
2. Installation procedure:  
A.  
Connect the TR-966D to 10/100Base-TX Device (Hub or  
Switch).  
4
5
 
 
Appendix Specification  
General  
Standard  
IEEE 802.3 10Base-T  
IEEE 802.3u 100Base-TX/100Base-FX  
Topology  
Protocol  
Star  
CDMA/CD  
Data Transfer Ethernet: 10Mbps(Half Duplex);  
Rate  
20Mbps(Full Duplex)  
Fast Ethernet: 100Mbps(Half Duplex);  
200Mbps(Full Duplex)  
Ports  
2 10/100Mbps RJ-45 ports  
2 SC Fiber ports  
( F1: 1310/1550 nm Single- mode single Fiber  
F2: 1550/1310 nm Single-mode single Fiber)  
LED indicator POWER Power on  
Each port RJ45 port:10/100Mbps Link/Act  
and 100Mbps speed LED  
Fiber port: 100Mbps Link/Act  
Network  
Medium  
RJ45 port: Cat. 5 Twist-pair  
SC Fiber port: single-mode fiber cable  
Max. Distance Twisted pair (Cat.5): 100m  
Single-mode fiber cable: 20km  
Environmental and Physical  
Power  
Dimension(LxWxH) 122mmx76mmx24mm  
Environment Operating temperature: 0ºC ~ 40ºC  
Power Adapter (9V, 0.8A)  
Storage temperature: -20ºC ~ 70ºC  
TP-LINK TECHNOLOGIES CO.,LTD.  
Humidity: 5% ~ 90% RH  
Add:3/F.,Buiding R1-B,Hi-tech Industrial Park,Shennan Rd.,Shenzhen,P.R.China  
6
 

Tektronix Portable Generator PFG 5105 User Manual
Toshiba Barcode Reader B 411 SERIES User Manual
Toshiba CRT Television 30HFX85 User Manual
Toshiba Digital Camera CS3950D User Manual
Toshiba DVD Player SD120 220 User Manual
Toshiba Network Card T2 Series User Manual
Tunturi Elliptical Trainer 3 Super User Manual
Univex Lawn Mower 425621X108 User Manual
Victor Technology Calculator 1430 3 User Manual
VTech Cell Phone LS6425 User Manual