TP Link Modem TD 8610 User Manual

TD-8610/TD-8610B  
External ADSL2+ MODEM  
Rev: 1.0.2  
1910010011  
 
FCC STATEMENT  
This equipment has been tested and found to comply with the limits for a Class B digital  
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the  
user is encouraged to try to correct the interference by one or more of the following  
measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which  
the receiver is connected.  
Consult the dealer or an experienced radio/ TV technician for help.  
This device complies with part 15 of the FCC Rules. Operation is subject to the following  
two conditions:  
1) This device may not cause harmful interference.  
2) This device must accept any interference received, including interference  
that may cause undesired operation.  
Any changes or modifications not expressly approved by the party responsible for  
compliance could void the user’s authority to operate the equipment.  
CE Mark Warning  
This is a class B product. In a domestic environment, this product may cause radio  
interference, in which case the user may be required to take adequate measures.  
 
Package Contents  
The following contents should be found in your package:  
¾
¾
¾
¾
¾
¾
One TD-8610/TD-8610B External ADSL2+ MODEM  
One AC power Adapter for TD-8610/TD-8610B External ADSL2+ MODEM  
One RJ45 cable  
Two RJ11 cable  
One ADSL splitter (only available for TD-8610)  
One Resource CD for TD-8610/TD-8610B External ADSL2+ MODEM, including:  
This User Guide  
Other Helpful Information  
Note:  
)
Make sure that the package contains the above items. If any of the listed items are  
damaged or missing, please contact with your distributor.  
 
CONTENTS  
 
TD-8610/8610B External ADSL MODEM  
Chapter 1. Product Overview  
With the excellent design of circuit and high quality production, we guarantee ADSL2+ MODEM a  
high performance, very good stability and easy to use.  
TD-8610/TD-8610B is a complete plug-and-play solution. With standard Ethernet interface, it can  
be directly connected to any 10M/100M Ethernet devices, support Auto-MDIX.  
TD-8610/TD-8610B not only use html (web mode through Ethernet port) to configure the MODEM  
but also use external utility software too. You can download it from our website  
1.1 Product main specification  
¾
¾
¾
¾
¾
¾
¾
¾
High speed and asymmetry data transmit mode, adapt to wide-band internet access  
Point to point connection, provide safe and exclusive bandwidth  
Support All ADSL industrial standards  
Advanced DMT modulation and demodulation  
Firmware upgradeable  
Compatible with all mainstream DSLAM (CO)  
Real-time Configuration and device monitoring  
Quick response semi-conductive surge protect circuit, provides reliable ESD and  
surge-protect function  
1.2 Supporting protocol  
- G.992.1 (G.dmt) - Annex A/B  
- G.992.2 (G.lite) - Annex A/B  
- ANSI T1.413  
- G.992.3 (ADSL2) - Annex A/B compliant  
- G.992.5 (ADSL2+) Annex A/B compliant  
- ADSL dual latency (fast path and interleaved path)  
- I.432 ATM physical layer compliant  
-Supports RFC2516 (PPPoE) *  
- Supports RFC1483 (EoA) ( Bridged)  
Note:  
)
“*”Need third-party software.  
1.3 Transmit data-rate  
¾
Max download data-rate: 24Mbps  
1
 
         
TD-8610/8610B External ADSL MODEM  
¾
¾
Max upload data-rate: 1Mbps  
Max line length: 6Km  
1.4 ATM property  
¾
¾
AAL0, AAL5, OAM, RM, and raw cell types supported  
Direct hardware support for 4 Receive VCs, with additional RX VCs and TX VCs supported in  
software  
¾
Full 24-bit Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI)  
1.5 System support  
¾
¾
¾
¾
Support PVC  
Support IEEE 802.3IEEE 802.3u  
Support 10Base-T/100BASE-TX full-duplex or half duplex Ethernet  
Support Auto-MDIX  
1.6 Working environment  
¾
¾
¾
Operating temperature: 0~40 ℃  
Storage temperature: -40~70 ℃  
Humidity: 10%90%  
1.7 Electric parameter  
¾
¾
Adaptor power Output: 9VAC/0.8A50Hz or 60 Hz  
Power consumption: 4W Maximum  
2
 
         
TD-8610/8610B External ADSL MODEM  
Chapter 2. Hardware Installation Guide  
2.1 System requirement  
Confirm your computer has been installed with networking interface card (NIC) before connecting  
ADSL MODEM to your computer, with operating system supporting the TCP/IP protocol.  
2.2 LED explanation  
The panel of ADSL MODEM includes one power button, one power indicator (RED) and four  
function indicators (GREEN), and these five indicators are explained as chart 1-1:  
Name  
Power  
Status  
Indication  
On  
Off  
On  
Power OK  
Power fail  
There is data transmitting or receiving on WAN  
port  
Act  
Off  
On  
Off  
No data transmitting or receiving on WAN port  
There is a mistake when ADSL is transmitting  
data or receiving data  
Alarm  
ADSL  
ADSL normal  
Slow flash  
Quick flash  
On  
Self-detecting when power up  
The LINE port is sending or receiving ADSL data  
The LINE port has connected to ISP’s network  
The LINE port is disconnected  
Off  
On  
LAN port is normal  
Off  
Connection on LAN port is abnormal  
Data is transmitting or receiving on LAN port  
LAN  
Flash  
Chart 1-1  
3
 
       
TD-8610/8610B External ADSL MODEM  
2.3 Rear-panel  
¾
¾
ON/OFF: Turn on/off the ADSL modem’s power.  
Power (9VAC/0.8A input): please do not use any unknown power adaptor, otherwise that  
may cause damage to your ADSL MODEM.  
¾
RESET (reset default): When the device is working, please press the reset button of the  
Modem, keep the reset button pressed down for more than five seconds and then wait for the  
router to reboot.  
¾
¾
LAN: Connect with your computer’s NIC.  
LINE (WAN): Connect to the MODEM of Splitter or connect to the telephone line.  
2.4 Hardware installation procedures  
First Step: Connect the MODEM of Splitter with the LINE port of the TD-8610/TD-8610B ADSL2+  
MODEM by telephone line. While you need to use a telephone, please attach telephone line into  
the phone of Splitter.  
Second Step: Connect category 5 cable with RJ45 jacks to ADSL MODEM’s LAN port and your  
computer’s NIC.  
Third Step: Link power adapter into the power jack of ADSL MODEM. Please note the range of  
voltage of power adapter should be within AC 220230V, 50Hz, which will make the MODEM  
under normal operation.  
Last Step: Check the line connection to see if everything is ready. Then power up.  
4
 
     
TD-8610/8610B External ADSL MODEM  
Figure 2-1  
5
 
TD-8610/8610B External ADSL MODEM  
Chapter 3. How to use  
3.1 Computer Configuration  
1. Connect the cable according to Chapter 2, and then turn on the power.  
2. Change the IP address of your PCFigure 3-1: Open TCP/IP Properties of the LAN card in  
your PC, enter the IP address as 192.168.1.* (* is any value between 2 to 254, Subnet mask  
is 255.255.255.0, Gateway is 192.168.1.1, DNS address is the value provided by ISP).  
Figure 3-1  
Note:  
)
1) The users of Windows 98 can open TCP/IP Properties according to the following:  
Right-press (Mouse) Network Neighbor -> Choose Properties -> Double-press TCP/IP. PCI  
Fast Ethernet Adapter.  
2) The users of Windows 2000/NT/XP can do the following: Right-press Network Neighbor ->  
6
 
       
TD-8610/8610B External ADSL MODEM  
Choose Properties -> Right-click Local Connection -> Choose Properties -> Double-press  
Internet Protocol (TCP/IP).  
3) The words in fact maybe are different with this guide.  
You can check whether your configuration is successful through PING command. Enter Ping  
192.168.1.1  
If the screen likes the following, your configuration is successful.  
Figure 3-2  
If the screen likes the following, your configuration is unsuccessful. Please repeat the previous  
steps again.  
Figure 3-3  
3.2 Login  
Startup Internet Explorer, and enter 192.168.1.1; then enter user name (admin), password  
(admin), you will see the page (Figure 3-4). When ADSL connection is OK, you will see some  
information such as link rate.  
7
 
   
TD-8610/8610B External ADSL MODEM  
Figure 3-4  
The default user name and its password is admin; if you want to change it, please go to  
"ManagementPassword". (Figure 3-5)  
Figure 3-5  
3.3 Setup  
1) Choose ATM PVCs Configuration (See Figure 3-6)  
2) Enter the VPI/VCI value which is provided by your ISP, click Save to finish the configuration.  
You can press Next to add VPI/VCI value.  
8
 
       
TD-8610/8610B External ADSL MODEM  
Figure 3-6  
3.4 Software Dial  
TD-8610/TD-8610B works in bridged (RFC 1483 Bridged) mode to connect to the Internet. You  
need to install dial software on your PC. There is some software working on WINDOWS in market,  
example for EnterNet3000, RASPPPoE and WinPeET.  
9
 
     
TD-8610/8610B External ADSL MODEM  
Appendix A: Default Configuration  
USER NAME  
PASSWORD  
IP ADDRESS  
VPI/VCI  
admin  
admin  
192.168.1.1  
0/32,1/33,0/35,0/100,0/200,8/35,8/81  
10  
 
   

Telstrat Network Card Argent User Manual
Thermador Ventilation Hood HS User Manual
Thermo Products Furnace GMC 85 User Manual
Thermo Products Stud Sensor USDT 2004B User Manual
Toshiba Computer Drive HDTB115XK3CA User Manual
Toshiba Security Camera IK TF7H User Manual
Tripp Lite Power Supply UL 60601 1 User Manual
UTStarcom Cell Phone CDM89215 User Manual
Verizon Cell Phone MFL69142601 User Manual
VTech Telephone LS6245 User Manual